Hi,
I am very new to this (Flashing) not the Mirage. Any help would be appreciated.
It would appear I successfully Flashed the Gotek. I believe the next step is to prepare a USB Stick but I am struggling to understand exactly how.
Basically all that happens on the Gotek display when I connect a Fat32 USB Stick is "003" continually flashes 3 times and then pauses for 2 seconds.
What should I be doing next?
Thanks in advance
edit*
So it turns out OSX incorrectly formatted the USB Stick and that is what the error code was suggesting. I have now managed to get a little further and have completed the UDP.
Now if anyone can suggest how to boot from the MASOS image I have on the USB Stick that would be appreciated.
Mirage Flashed Gotek Troubles
Re: Mirage Flashed Gotek Troubles
You can found some Mirage images for the HxC on this forum :
Here for example :
http://torlus.com/floppy/forum/viewtopi ... =17&t=3043
Use the indexed cfg file and rename the hfe files DSKA0000.HFE,DSKA0001.HFE,DSKA0002.HFE,DSKA0003.HFE...
Here for example :
http://torlus.com/floppy/forum/viewtopi ... =17&t=3043
Use the indexed cfg file and rename the hfe files DSKA0000.HFE,DSKA0001.HFE,DSKA0002.HFE,DSKA0003.HFE...
Re: Mirage Flashed Gotek Troubles
Thanks Jeff, that's pretty much what I have been doing, trawling the boards for Mirage files and naming them appropriately and placing them with different cfg files.
I have seen some people talk about the jumper locations being critical and also perhaps flipping the ribbon cable over?
I just don't seem able to hit the right combination, I assume the first file will automatically load if everything is correct?
I have seen some people talk about the jumper locations being critical and also perhaps flipping the ribbon cable over?
I just don't seem able to hit the right combination, I assume the first file will automatically load if everything is correct?
Re: Mirage Flashed Gotek Troubles
If a file is loaded, you should see a number on the screen. "000" for the the first one.j1mpst3r wrote: ↑Fri Nov 17, 2017 12:06 am Thanks Jeff, that's pretty much what I have been doing, trawling the boards for Mirage files and naming them appropriately and placing them with different cfg files.
I have seen some people talk about the jumper locations being critical and also perhaps flipping the ribbon cable over?
I just don't seem able to hit the right combination, I assume the first file will automatically load if everything is correct?
For the jumper set it to S0.
Re: Mirage Flashed Gotek Troubles
I see the numbers corresponding to the files on the Gotek display. i.e if I have 4 files there are 4 numbers 000,001,002,003
However the Mirage doesn't react, the Mirage shows a horizontal line at the top of it's display.
However the Mirage doesn't react, the Mirage shows a horizontal line at the top of it's display.
Re: Mirage Flashed Gotek Troubles
Is the drive green led always lit ?
Re: Mirage Flashed Gotek Troubles
yes, solid
*edit
Wooohooo, flipped the ribbon cable over and it's working
Thanks for your input Jeff, fantastic product, service and support.
Got the Magic "21"
*edit
Wooohooo, flipped the ribbon cable over and it's working
Thanks for your input Jeff, fantastic product, service and support.
Got the Magic "21"
Last edited by j1mpst3r on Fri Nov 17, 2017 1:27 am, edited 1 time in total.
Re: Mirage Flashed Gotek Troubles
then reconnect the floppy ribbon to the other way.
Re: Mirage Flashed Gotek Troubles
Thanks Jeff, must have been a delay in displaying your last advice on the Board. I thought you had gone to bed and rightly so
Re: Mirage Flashed Gotek Troubles
Refresh page is needed to see new posts