Hi,
I have managed to acces the SD card and scroll true the HFE's.
But now when i select a HFE file, i see TRACK 2 and freezes.
Also my D4 and D3 led's are never burning (led's are OK, did a diode test)
Can someone point me in a good direction please, i'am almost there i think!!!
Thanks a lot.
Cheers,
Jasper
Freez at TRACK 2
-
- Posts: 25
- Joined: Fri May 08, 2009 10:01 am
Hmmm at the moment i'am using a twisted cable and seems that the led D4 is blinking 2 times after a reset.
Also in my Workbench i've got DF0:?????
When i select a HFE it says
Track 0 (and stays there)
Altought when i don't have a SD card in it, the D4 led is blinking once in a 4 seconds.
Any suggestions on how to load the HFE's ?
it looks like the same problem XYBOTS has had, but he did'nt answering anymore:
Cheers,
Jasper
Also in my Workbench i've got DF0:?????
When i select a HFE it says
Track 0 (and stays there)
Altought when i don't have a SD card in it, the D4 led is blinking once in a 4 seconds.
Any suggestions on how to load the HFE's ?
it looks like the same problem XYBOTS has had, but he did'nt answering anymore:
xybots wrote:
hi every one urgent help needed
when i connect the floppy cable to the Amiga computer the d4 led lights up i switch the Amiga on and d4 goes off when the Amiga logo comes up and the floppy light on the Amiga goes out, i select an image from the SD card and press switch s3 then on the LCD it switchs to saying track 0 and freezes there and d4 just blinks intermittently ive tried several different images of different things and i am now baffled any help would be very much appreciated
Cheers,
Jasper
hi jasperfreshworks wrote:Hmmm at the moment i'am using a twisted cable and seems that the led D4 is blinking 2 times after a reset.
Also in my Workbench i've got DF0:?????
When i select a HFE it says
Track 0 (and stays there)
Altought when i don't have a SD card in it, the D4 led is blinking once in a 4 seconds.
Any suggestions on how to load the HFE's ?
it looks like the same problem XYBOTS has had, but he did'nt answering anymore:
xybots wrote:
hi every one urgent help needed
when i connect the floppy cable to the Amiga computer the d4 led lights up i switch the Amiga on and d4 goes off when the Amiga logo comes up and the floppy light on the Amiga goes out, i select an image from the SD card and press switch s3 then on the LCD it switchs to saying track 0 and freezes there and d4 just blinks intermittently ive tried several different images of different things and i am now baffled any help would be very much appreciated
Cheers,
Jasper
i replaced the 74ls01 chips and made sure the voltage was 9v and they are working hope this helps, both my boards are working now. if you need more help let me know.
no it doesn't freeze: push the middle button to select another file._Nikanor_ wrote:Hi to everybody!
I have the same problem.
When i try to load HFE converted from MSX-DOS .DSK file, display shows
TRACK 2_ and freezes.
Is that common problem to all boards?
And what should i try to fix this situation?
Thanks.
what is your system ? didn't you have put the configuration jumper at the right place?
the write support works only on 256 and 512 Bytes/sectors MFM disk. what is your target computer?_Nikanor_ wrote:Ok, everything works fine now!
It was wrong cable positioning.
Another issue - can't write anything to disk. Copying by system is ok but phisically no file added to image. Maybe old firmware?
How to check, what firmware version is, without PIC flasher?